Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Farm & ranch
Before
After
Before
After
Before
AfterFAAC Gate Access Control in Grand Prairie: What to Know First
We repair and service FAAC gate access control systems throughout Grand Prairie, including keypads, remote receivers, phone entry, card readers, video intercoms, and smartphone access. Most jobs are diagnosed and fixed in a single visit, and the price is quoted and agreed before any work starts. If you’ve got a FAAC gate that won’t open, a keypad that’s gone dead, or a system that opens for some people and not others, call (903) 829-4499 and Hal or one of his crew will walk you through what’s likely going on before you spend a dime.
This page is for Grand Prairie homeowners who own a FAAC swing or slide gate operator and need the access side of it working right. Not the gate itself wobbling (though we handle that too), but the part that decides who gets in. That’s a different skill set than gate mechanics, and it’s one we’ve been building since 2001.
How FAAC Products Fail - and How We Fix Them
- FAAC 400 and 412 series: phantom openings at dusk. The photocell inputs on these older swing-gate boards get flaky with age, and in Grand Prairie’s summer heat they degrade faster than the spec sheet admits. The gate will open for no reason and sit there, or worse, start closing while a car is halfway through. We bypass the failing input at the board, set the obstruction logic correctly, and replace the photo eyes rather than the whole operator. Most shops quote a new board at this point. We’ve fixed dozens of these without one.
- FAAC E024U control board: keypad works, remotes don’t. The plug-in receiver modules on the E024U are a known weak spot. They’re cheap from FAAC, but heat and moisture in an unvented Grand Prairie gate box cook them. We stock replacement modules and also harden the box - a vent kit costs pennies and doubles the life of the receiver. A lot of gate companies just tell you to buy a new remote, sell you one for $60, and leave before you realize the old remote was fine.
- FAAC 750 and 760 slide operators: access control loop interference. These slide units share a ground plane with the loop detector wiring, and in Grand Prairie where driveway loops get cut and spliced by every concrete and landscape contractor who’s ever worked the yard, the splices corrode and the board reads a phantom vehicle sitting on the loop. The gate won’t close, or won’t open because it thinks someone’s in the way. We test the loop resistance, find the bad splice, and repair it. We don’t just crank the loop sensitivity and call it done.
- FAAC S418 keypad: buttons go intermittent after two or three Texas summers. The membrane on the S418 was never built for UV exposure like we get here. The top row dies first - usually the 1, 2, and 3 keys. It’s a flawed design, not a bad homeowner. We replace the keypad face with a harder-wearing aftermarket unit and add a small sun shield, which FAAC doesn’t sell but takes us ten minutes to fabricate in the truck. Your code stays the same.
- FAAC phone entry systems paired with VOIP lines. If you switched from a landline to a VOIP service and now the gate won’t dial out, that’s not a FAAC fault - it’s a line-voltage mismatch. FAAC phone modules were designed for copper. VOIP runs lower voltage, so the module can’t trigger the relay. We add a small line-conditioning relay so the system works with the phone line you actually want, not the one the manufacturer assumed you’d keep.
One thing worth saying plainly: we are an independent FAAC service provider. We’re not affiliated with or authorized by FAAC, and we don’t pretend to be. We buy genuine FAAC parts when they’re needed, and we use tested aftermarket parts when they’re the better call for a Texas driveway. We tell you the difference before we install anything.
Our FAAC Gate Access Control Process
- 1
Call and describe the symptom. You get a live person, not a menu. Tell us what the gate does or doesn’t do. Hal’s signature line applies: “Tell me what it’s doing, and I’ll tell you what it needs. No runaround.”
- 2
We arrive and verify with you present. We watch the gate behave badly. We don’t take your word for it and we don’t guess from the driveway before you’ve had coffee. If the problem won’t repeat, we don’t replace parts on a hunch.
- 3
Board-level diagnostics first. We meter the access control circuit from the keypad or reader back to the FAAC board before touching anything. Half the time the problem is a broken conductor or a failed safety edge, not the opener.
- 4
Parts decision in plain language. Genuine FAAC module, or quality aftermarket with the same rating and a better lifespan. We show you the old part and explain what failed. You approve the price before anything goes in.
- 5
Repair, test, and hand off. We test every input - keypad, remote, phone, loop. Then we run the gate through five full open-and-close cycles with you standing there.
- 6
90-Day Done Right Promise in writing. If anything about that repair fails in 90 days, you call and we come back. No arguing about whose fault it was. Hal’s name is on it.
What FAAC Gate Access Control Costs in Grand Prairie
Here’s what we see on FAAC jobs around Grand Prairie:
- Keypad replacement or repair: $180-$340
- Remote receiver module replacement: $160-$290
- Phone entry system repair or line-conditioning relay: $220-$390
- Video intercom repair (screen or panel side): $280-$520
- Card reader or standalone access pad install: $240-$460
- Full-board replacement on older FAAC 400-series: $420-$780
What moves the price is whether you’ve got an easy keypad swap or a full integration with photo eyes, loops, and phone wiring. The price we quote is the price you pay. No trip charge inside the county. And remember, $40 off any repair over $200, plus a permanent 10% discount for seniors and veterans. Call (903) 829-4499 for a free estimate.
Why Grand Prairie Homeowners Call Gatewood Fence & Gate for FAAC Work
Because when your gate system quits, you don’t want a guy who’s read one FAAC manual. You want the person who’s been fixing gates in Grand Prairie since 2001 and knows, from experience, that a FAAC 400 in the Dalworth Park neighborhood fails differently than the same unit over near Joe Pool Lake. We’ve got the reputation because we earned it one gate at a time.
Hal Gatewood’s name is on the shop. The address is published. You can drive over and look him in the eye. His crew is background-checked and uniformed, and they’ve been with him long enough to know a FAAC board from a generic one without squinting. If your FAAC proves beyond saving, we service LiftMaster, Mighty Mule, Ghost Controls, and DoorKing too, so you’ll get a straight recommendation for what actually fits your gate, not a lecture.
FAQs
If you’re outside the manufacturer’s warranty period, no. Most FAAC systems in Grand Prairie are well past it, and as an independent FAAC service provider, we work warranty-safe so the repair doesn’t compromise the rest of the unit in a way a future claim could be denied. We use genuine FAAC parts when the job calls for it and don’t modify boards in ways that would void a live warranty.
Most FAAC repairs can be scheduled within 24 to 48 hours, and if your gate is stuck open or won’t open for emergency vehicles, we move it to the front of the line. A live person answers the phone around the clock, so call (903) 829-4499 and tell us what the gate is doing. You’ll know when we’re coming before you hang up.
We keep the common failure items in the truck - remote receiver modules, keypad faces, safety edge parts, and relay modules for the older 400 and E024U boards. Less common items take a few days from our supplier. We’ll tell you which situation you’re in before we start, so there’s no surprise wait.
If the board is original and the gate operator itself is over 15 years old, replacement sometimes costs less than throwing good parts at a tired motor. But if it’s a bad keypad, a failed receiver, or a wiring fault, we fix it and you keep a system that has years left. We’ll give you an honest number for both options and let you decide.
Usually not. A remote dropping out alongside a gate that doesn’t fully close often points to the same thing - a failing receiver module or a low-voltage condition at the board. We diagnose the whole access system at once, not one symptom at a time, so you’re not paying for two service calls that should have been one. Call (903) 829-4499 and we’ll get it sorted.
Written by Hal Gatewood, Owner, Gatewood Fence & Gate at Gatewood Fence & Gate, serving Grand Prairie and nearby areas.