Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Farm & ranch
Before
After
Before
After
Before
AfterGhost Controls Gate Parts & Welding in Grand Prairie: What to Know First
Ghost Controls gate parts and welding in Grand Prairie are handled right at your driveway. We diagnose the failed component, weld on site when the frame or hinge post is the problem, and get your gate swinging again, usually the same day for hinge and rail repairs. Estimates are free, the price is agreed before any work starts, and every job carries our 90-Day Done Right Promise in writing.
This page is for homeowners around Grand Prairie who own a Ghost Controls opener on a welded steel or aluminum gate and need honest answers about parts, welding, and whether the opener you have is even worth keeping. Call (903) 829-4499 and a real person picks up.
Key Takeaways
- We’re an independent Ghost Controls service provider, not an authorized dealer.
- On-site welding means your gate never leaves the property.
- OEM and quality aftermarket parts are both on the table, and we tell you which one makes sense.
- Free estimates, no trip charge inside the county, and $40 off any repair over $200.
How Ghost Controls Products Fail - and How We Fix Them
Ghost Controls builds dependable openers, but the opener is only half the system. Around Grand Prairie, the gate frame, hinges, and posts take a beating from wind and shifting clay soil. Here’s what we actually find when a Ghost Controls gate stops working right.
- Hinge post movement on the Armor line. The Ghost Controls Armor series pulls hard on the first swing. In Grand Prairie’s clay soil, a post set in shallow concrete leans within a couple of seasons. The opener then pushes against a moving frame, the travel limits drift, and the motor labors. We cut out the old post, weld a heavier one with deeper set, and the opener stops fighting itself.
- Operator bracket welds cracking around the TSS1 and TDS2. These models mount on a bracket that gets welded or bolted to the gate frame. If the original install used a bracket too light for the panel weight, the weld fails at the bracket edge. We see it as a hairline crack first, then the bolt holes oval out. Fix is a heavier bracket welded to the frame, not just re-tightened bolts.
- Gate sag that kills the auto-close sensor alignment. Every Ghost Controls opener with auto-close relies on the magnet and sensor staying lined up. When the gate sags a half inch, the magnet misses, the gate thinks it’s open, and the system shuts down or reverses. A sagging gate is a hinge post problem, not a sensor problem. We weld the hinge back into true alignment and retrain the limits.
- Bent or broken gate rail on double-swing setups. The rail carries the weight of the second leaf on a double gate. When a wheel or roller seizes, the rail takes the twist. We straighten or replace the rail, weld the hangers back square, and replace the roller so it doesn’t happen again next season.
- Latch strike misalignment after panel flex. Ghost Controls gate locks and latches are built to a tight tolerance. Panel flex from wind loading moves the strike plate a quarter inch, and the latch binds. We weld a reinforced strike mount that holds alignment better than the original thin tab.
Our Ghost Controls Gate Parts & Welding Process
Every Ghost Controls job around Grand Prairie follows the same steps. No surprises, no haul-off, no invoice that grows after we start.
- 1
Call and we answer. Tell us what the gate is doing. Hal will ask enough questions to know if it’s a parts job, a welding job, or both.
- 2
We come out and look. Free estimate, no trip charge inside the county. We show you what failed and why it failed before we touch anything.
- 3
Parts decision, your call. If the Ghost Controls part needs replacing, we explain OEM versus quality aftermarket. If it’s a frame issue, we quote the weld repair. Price is agreed before work starts.
- 4
The repair or weld happens on site. Your gate stays in your driveway. The welding truck carries everything we need, no running back to the shop.
- 5
We test the whole system. Limits, force settings, auto-close, safety edges, the manual release. Not just the part we touched.
- 6
You get the 90-Day Done Right Promise in writing. If it’s not done right, one call brings us back. No runaround.
What Ghost Controls Gate Parts & Welding Costs in Grand Prairie
Here are real ranges we quote around Grand Prairie for common Ghost Controls repairs. Every price is agreed before we start, and the free estimate locks it in.
- Hinge replacement (welded, single gate): $180-$320 depending on panel weight and post condition
- Post replacement with concrete set and welded hinge: $350-$650 for a standard residential post
- Gate rail repair or replacement (double gate): $220-$480 including rollers
- Custom welding on a cracked frame or bracket: $150-$400 depending on steel thickness and access
- Latch and lock replacement with reinforced strike: $120-$280
- Ghost Controls opener part replacement (limit switches, sensor, control board): $90-$350 for the part, plus standard labor
What moves the price is panel weight, post depth, and how much of the old weld has to be cut out before we can start clean. Call (903) 829-4499 for an exact quote, and remember: $40 off any repair over $200, and a permanent 10% discount for seniors and veterans.
Why Grand Prairie Homeowners Call Gatewood Fence & Gate for Ghost Controls Work
Hal Gatewood has been fixing gates in Grand Prairie since 2001. Most folks around Dalworth Park know his truck on sight. He picked up his welding and mechanical trade at Tarrant County College’s vocational program before going out on his own. The name is on the shop, and the shop is down the road, and that is the oldest accountability there is.
We service nine major gate brands, so when a Ghost Controls opener is paired with a LiftMaster gate panel or a Mighty Mule legacy install, we work on it without blinking. DoorKing too. The person who shows up is background-checked, uniformed, and actually knows Ghost Controls boards and limits, not just how to bolt on a new part. And if we ever run across a job where the opener is done but the gate frame is worth saving, that is exactly the job we want. We weld on site, we stand behind it for 90 days, and we answer the phone when you call.
FAQs
Yes, when the part matters, like control boards, limit switches, and remotes. For brackets, rollers, and certain hardware, we use quality aftermarket equivalents that are often heavier than OEM. We show you what we’re putting on and why.
Welding on the gate frame does not touch the Ghost Controls opener itself, so the opener warranty stays intact. We keep weld heat away from electronics and use heat-sinking cloth when we’re working within a few inches of a mounted operator.
For hinge, rail, and latch failures, most Grand Prairie calls get same-day service. Post replacement that needs concrete set is usually next day or scheduled within 24 hours. Call (903) 829-4499 and ask directly, and Hal will tell you what’s realistic, not what you want to hear.
If the operator’s control board and motor are fine, repairing the welded frame and hinge posts is almost always the better money. A new gate with a weak post does the same thing in two years. We’ll tell you if the panel is too far gone, and that judgment is free.
Most residential hinge replacements run $180 to $320. Heavy panels, double gates, and posts that need work push the price up. You will know the price before we start. Call (903) 829-4499 and we’ll come out free.
Written by Hal Gatewood, Owner, Gatewood Fence & Gate at Gatewood Fence & Gate, serving Grand Prairie and nearby areas.