FAAC Gate Motor & Opener Nationwide | Gatewood Fence & Gate

FAAC Gate Motor & Opener in Grand Prairie: What to Know First

FAAC gate motor and opener repair in Grand Prairie is work we do every week, and most jobs are diagnosed in one visit and fixed same-day when the part is on the truck. An honest price range for FAAC opener service here runs $185-$650 depending on whether it’s a limit switch, a control board, or a full operator swap. If your FAAC gate won’t open, won’t close, or starts and stops on its own, call (903) 829-4499 and you’ll get a live person. This page is for FAAC owners in Grand Prairie who want a straight answer on what’s wrong and what it’ll take to fix it, without the runaround.

Call (903) 829-4499

How FAAC Products Fail - and How We Fix Them

FAAC builds a solid operator, but every brand has its habits. Here’s what we actually find when a FAAC gate starts acting up in Grand Prairie:

• FAAC 400 and 402 operator hums but the gate doesn’t move. Nine times out of ten this is a 10-year-old capacitor that’s drifted out of spec, not a bad motor. Some shops will quote a full operator replacement. We test the capacitor first, swap in the correct microfarad rating, and you’re back rolling for under $200.
• FAAC 400/402/412 won’t close all the way, then reverses. On FAAC swing operators, the culprit is usually the mechanical travel stops riding against the worm gear housing and throwing the torque sensor off. We adjust the stop bolts, check the motor’s current draw, and set the limit cams where they should have been from the start.
• FAAC 844 and 391 slide gate opens fine but grinds or stalls halfway. In Grand Prairie clay soil, gate rollers sink and the chain or rack goes out of true. The operator struggles against a gate that’s fighting the track. We level the gate, replace the worn rollers with sealed bearings, and reset the rack so the motor isn’t pushing uphill.
• FAAC E024 board loses its programming after a storm. North Texas lightning is hard on low-voltage gate boards. The E024’s factory settings revert, the remote codes erase, and the gate won’t respond. We reflash the board, re-learn your remotes and keypad, and check the ground path so the next storm doesn’t do it again.
• FAAC Photobeams trip for no reason, or the gate ignores them entirely. The beams are the safety edge on a FAAC swing. We find misaligned lenses, sun glare from the west-facing side of Grand Prairie lots, or corroded spade connectors. Cleaning, realigning, and sealing the connections usually costs less than $150.

We also see FAAC battery backup units that were never wired to a dedicated circuit, so the gate goes dead when the lights flicker. That’s a quick fix most owners don’t know they need until the driveway gate traps them on the wrong side.

Our FAAC Gate Motor & Opener Process

When you call about a FAAC operator in Grand Prairie, here’s how it goes:

1. 1
   You describe the symptom. Tell us what the gate is doing, or not doing. Hal will ask a few questions that usually point to the failing component before we even put the truck in gear.
2. 2
   We come out, free of charge inside the county. No trip charge. We pull the FAAC cover, meter the board, test the capacitor, and check the mechanical side: the arm, the hinge, the stops, the gate’s weight and level.
3. 3
   You get a straight diagnosis and a written price. We show you exactly what we found and what it costs to fix, before any work begins. No surprises at the end.
4. 4
   We fix it with OEM or quality aftermarket, depending on what’s wisest. For a FAAC under warranty, we use OEM FAAC parts to keep the warranty intact. For an older FAAC 400 or 402, a reputable aftermarket capacitor or limit switch often saves real money without cutting corners. We tell you which before you spend a dollar.
5. 5
   We test the gate through at least a dozen cycles. Open, close, reverse on obstacle, remote, keypad, the works. We watch the motor’s amp draw and listen for strain. If something’s not right, we catch it before we leave.
6. 6
   You get the 90-Day Done Right Promise in writing. If the FAAC acts up within 90 days on the same repair, one call brings us back. No fight, no fine print.

What FAAC Gate Motor & Opener Costs in Grand Prairie

Here’s what FAAC owners in Grand Prairie typically spend with us, based on jobs we’ve done in the area:

• Capacitor replacement (FAAC 400/402 hums, no movement): $135-$195 installed, including the part.
• Limit switch or travel stop adjustment: $145-$185, labor and parts together.
• FAAC E024 or 455D control board replacement: $380-$650, depending on the board revision and whether it’s OEM or a quality compatible board.
• Full FAAC operator replacement on an existing gate: $1,200-$2,800, installed with new arms, brackets, and a proper ground check.
• Photobeam repair or replacement: $120-$180 for the pair, installed and aligned.

What moves the price is the age of the operator, whether it’s a 400-series swing or a 844 slide, and whether the gate itself is fighting the motor. We’ll always quote the repair before we spin a wrench. Call (903) 829-4499 for a free estimate with zero obligation.

Why Grand Prairie Homeowners Call Gatewood Fence & Gate for FAAC Work

We’re local. Hal Gatewood has been fixing gates in Grand Prairie since 2001, and his name is on the shop and on every invoice. Most folks around Dalworth Park know the truck. We know the FAAC 400 and 402 like the back of our hand because they’re on a hundred driveways within ten miles of here, from Westchester to Country Club Estates. And if your FAAC operator turns out to be a lost cause, we don’t dance around it. We’ll tell you straight whether repair or replacement makes sense, and we service the other major brands too: LiftMaster, Mighty Mule, Ghost Controls, and DoorKing. That matters when you’re deciding whether to stay with FAAC or switch.

Every FAAC job we do carries the 90-Day Done Right Promise in writing. Calls are answered by a live person 24/7, not a voicemail. And you’ll get a fair price up front: $40 off any repair over $200, no trip charge inside the county, a free second opinion on any written estimate, and 10% off for seniors and veterans. Hal put his name on this shop 29 years ago in the fencing trade, and he still answers the phone.

FAQs