Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Farm & ranch
Before
After
Before
After
Before
AfterFast, Reliable Gate Installation Across Cedar Hill
New gate installation in Cedar Hill usually runs $2,400 to $7,800 for a standard driveway swing gate, $3,100 to $9,500 for a double gate, and $1,800 to $4,600 for a pedestrian gate, with the final number set by footing depth, slope work, and HOA finish requirements. We quote the price before any work starts and that price does not change at the door. Hal Gatewood has been building and hanging gates since 2001, and he will be the one who answers when you call (903) 829-4499.
Most of the calls we take from Cedar Hill involve the same two starting points: an HOA letter saying the gate needs architectural approval, and a driveway that climbs or drops enough that a standard flatland install would drag the gate leaf on the first season. We handle both from the first visit. You will get a written price, a straight answer on what the slope means for your swing arc, and no trip charge inside the county.
Why Gatewood Fence & Gate Is Cedar Hill’s Preferred Gate Installation Company
We do not send a rotating cast of subcontractors to Cedar Hill. Hal Gatewood owns the company, his name is on the invoice, and the person who shows up to measure your driveway is the same person who will stand behind the work for 90 days. That promise is in writing on every job: if it is not done right, one call brings him back. No runaround, no “that is a different crew,” no phone tree.
Cedar Hill homeowners have a specific problem that flatland gate companies do not understand until it is too late. The Balcones Escarpment puts limestone bedrock as shallow as 14 to 18 inches under a lot of the city, especially up near Cedar Hill State Park and the elevated west side. A crew that shows up with a standard post-hole digger will stall out immediately. We expect rock here and bring the drill rig the first time. That is not extra, that is the job done right the first time, and it is why we tell people to ask any installer whether they have drilled limestone in Cedar Hill before they sign anything.
We also know the HOA rhythm in Cedar Hill. Brick-front subdivisions built in the 1990s and 2000s dominate the city, and nearly all of them require architectural review before a gate goes up. We will help you pull together the drawings, the finish spec, and the height details the committee wants to see. We have sat through enough of those reviews to know what gets approved and what gets sent back.
Our Gate Installation Services in Cedar Hill
Every Gate Installation we do in Cedar Hill starts with a site visit, not a phone estimate. We need to see the grade, check for rock, and measure the actual swing path. Here is how that plays out across the gate types we install most in this city.
Driveway Gate
Driveway gates in Cedar Hill are where the escarpment causes the most trouble. A driveway that climbs toward the house changes the geometry of a swing gate leaf, and if the installer does not compensate for the arc, the gate drags or stops latching. We calculate the slope before we order steel and set the hinges accordingly. Standard single driveway gates in Cedar Hill run $2,400 to $5,500 installed, plus any operator and access control.
Pedestrian Gate
A pedestrian gate is the workhorse of a Cedar Hill side yard, and it is the easiest place to spot cheap work. Hinge posts set in Blackland Prairie clay will tilt within a season if the footing is only two feet deep. We set post footings below the active clay zone and weld the frame square before it leaves the truck. Pedestrian gate installs typically run $1,800 to $4,600, and most are done in a single day.
Sliding Gate
Sliding gates make sense on short or steep Cedar Hill driveways where a swing gate would need too much room to arc. They also hold up better on grades because the gate rides on a track instead of hinging against the slope. The catch is that the track bed has to be dead level and the operator has to be sized for the gate’s weight, not the other way around. Expect $3,400 to $9,800 depending on steel, operator, and access control.
Swing Gate
Most Cedar Hill properties we visit want a swing gate, and the city’s HOA-heavy subdivisions usually require a specific look: black powder-coated ornamental steel, matching picket spacing, and a set height. We match those specs and build the gate to handle the slope. Double swing gates on a sloped driveway need arc compensation on both leaves, or they bind in the middle. We handle both single and Cedar Hill double swing installs with the same site-first approach.
Double Gate
Double gates are the standard for wider Cedar Hill driveways and for subdivision entry points. The failure point is almost always the center: the two leaves sag inward and the latch stops meeting. That sag starts at the hinge post, and a post set in shallow rock or active clay will move. We run double gates from $3,100 to $9,500, with the biggest cost drivers being operator automation, access control, and how much rock we hit when setting the posts.
Security Gate
A security gate in Cedar Hill is not just a taller panel. It means a reinforced frame, a heavier operator, and access control that actually works for the people who live there. We install shared entry systems for gated communities, including keypads, remotes, and phone-based entry. For a single home, a security-rated gate with operator and keypad typically starts around $4,200 and goes up from there based on footage and access needs.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Cedar Hill
We install and service operators from Linear, Viking, Ghost Controls, and DoorKing, and we keep common Cedar Hill parts on the truck: control boards, photo eyes, remotes, and battery backup units. That matters in July, when an unshaded operator enclosure on the east side of the escarpment hits 110 degrees and the board cooks. We do not tell you to wait two weeks for a part to ship. If it is a common failure, we likely have it with us. Hal and his crew are certified on nine major brands, and we will tell you straight if your existing operator is worth saving or if you should put that money toward new.
Common Gate Installation Problems We See in Cedar Hill Homes
These are the patterns we walk into on repeat in Cedar Hill. If any of them sound familiar, the fix is usually less than a full replacement, but only if it is caught early.
- Posts leaning on shallow limestone. An auger hits rock at 14 to 18 inches, the installer calls it “good enough,” and six months later the hinge post has tilted a full inch. The gate sags, the latch misses, and the whole thing has to be re-set. We drill into the limestone and set the post deep with rebar so it stays where it belongs.
- Gate frames racked by Blackland Prairie clay. The clay here swells in spring rains and shrinks in drought. That seasonal heave pulls gate frames out of square, especially on the east and lower sections of Cedar Hill where the clay is deepest. A frame that is not square will bind at the hinges and wear the operator out fast.
- Swing gates dragging on sloped driveways. Near Cedar Hill State Park and the elevated west side, driveways climb enough that a standard swing gate leaf scrapes the concrete on the low side. The fix is arc compensation at the hinge, and it has to be designed in from the start. Retrofit fixes are possible but cost more than doing it right the first time.
- Operator boards dying in unshaded enclosures. Triple-digit heat in July and August kills circuit boards and battery backups inside black steel enclosures. We see a spike every summer in Cedar Hill, and the fix is a ventilated enclosure, a heat shield, or a different mounting location, not just a new board every year.
Pricing for Gate Installation in Cedar Hill, TX
Here are the honest numbers for Cedar Hill, based on what we have built here. Single driveway swing gate: $2,400 to $5,500. Double swing gate: $3,100 to $9,500. Pedestrian gate: $1,800 to $4,600. Sliding gate with track: $3,400 to $9,800. Security gate with access control: starts around $4,200. All prices include materials, labor, hardware, and the 90-Day Done Right Promise in writing. The two Cedarl Hill-specific variables that change the number are rock drilling, which runs $300 to $900 depending on how deep the limestone sits, and slope compensation for the swing arc. We quote those on the first visit, and the price is agreed before any steel gets ordered. No trip charge inside the county, $40 off any repair over $200, and a permanent 10% discount for seniors and veterans.
We Also Serve Cities Near Cedar Hill
If you are in DeSoto, Duncanville, Mansfield, or Arlington, the same crew that works Cedar Hill covers your driveway too. The flatland clay issues change, the escarpment rock less so, but the way we quote and build does not. Call (903) 829-4499 and we will come measure.
Serving Cedar Hill, TX - Our Local Coverage Area
We’re based in the Cedar Hill area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Installation in Cedar Hill
Yes, in most Cedar Hill subdivisions you need architectural review approval before a new gate goes in, and that approval usually covers gate style, height, finish color, and sometimes the operator type. We will help you prepare the submittal with drawings and specifications that match what the committee expects to see for Cedar Hill’s brick-front HOA neighborhoods. Call (903) 829-4499 before you start the paperwork and we will tell you what your specific HOA is likely to require.
A sloped driveway shortens the effective arc of a swing gate, so the gate leaf can drag on the low side or fail to close fully at the latch. We measure the grade before we order steel and build hinge compensation into the gate so it swings clean on the slope. This is the single most common flatland installer mistake we correct in Cedar Hill, and it is cheaper to do it right the first time than to re-hang a dragging gate later.
On shallow limestone, which is common near Cedar Hill State Park and the elevated west side, the footing has to be drilled into rock and the post set with rebar, not just dropped into an 18-inch augered hole and packed with concrete. We drill to solid bearing and set the hinge posts deep enough to hold a heavy steel gate without leaning. A post set short in Cedar Hill will tilt within a year.
Yes, we install shared entry systems for gated communities in Cedar Hill, including telephone-based entry, keypads, remotes, and vehicle detection loops. We coordinate with the management company so residents keep access during the changeover. Call (903) 829-4499 and we will come look at your entry point and write up a plan with a fixed price.
The Blackland Prairie clay in the lower and eastern sections of Cedar Hill swells with spring rain and shrinks in summer drought, which moves the soil under the posts and racks the frame out of square. The gate then binds at the hinges and the operator works harder until it fails. Deeper footings and a welded, rack-resistant frame design stop most of the seasonal movement before it becomes a repair.
If you have a gate project in Cedar Hill, call (903) 829-4499 for a free estimate. Hal will answer, and he will tell you what the slope, the rock, and the HOA mean for your gate before you spend a dollar.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate, serving Cedar Hill since 2001.