Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Farm & ranch
Before
After
Before
After
Before
AfterFast, Reliable Gate Parts & Welding Across Duncanville
Gate parts and welding in Duncanville usually comes down to one thing: black clay. If your swing gate bound up in August after latching fine in May, or your slide gate operator quit after a heavy rain, the soil under your posts moved. That’s the job. We fix it on site. Hal Gatewood has been welding and repairing gates since 2001, and our Gate Parts & Welding crew works Duncanville driveways every week. Call (903) 829-4499 and a live person answers, any hour.
Why Gatewood Fence & Gate Is Duncanville’s Preferred Gate Parts & Welding Company
We’re not a call center and we don’t send a rotating cast of subcontractors. The person who answers the phone is the same outfit that shows up at your gate on Danieldale Road or over near Red Bird Lane. Hal’s name is on the shop and on every invoice. That matters when you’re deciding whether to trust a weld on a 50-year-old wrought-iron gate your grandmother installed.
What Duncanville homeowners tell us they hate most is the bait-and-switch: a low phone quote, then a surprise invoice at the door. We don’t work that way. The price gets written down and agreed to before any welding starts, and the 90-Day Done Right Promise is stamped on every job. If the hinge we replaced works loose or the post we reset starts leaning again, one call brings us back.
Duncanville’s older neighborhoods south of Wheatland Road and the acreage properties east toward Cedar Hill line are where we spend a lot of our time. These gates are 40 to 60 years old, set in footings that were never deep enough for Blackland Prairie clay. We know that before we ever pull up.
Our Gate Parts & Welding Services in Duncanville
Hinge Replacement
When a Duncanville gate starts dragging on the latch side, most people assume the hinge is worn out. Sometimes it is. But more often the hinge post has leaned outward as the clay dried and shrank away from the footing. We’ll tell you which one it is, and we’ll fix the thing that’s actually broken. A hinge replacement on a standard tubular-steel driveway gate in Duncanville typically runs $180 to $320 per hinge, including grinding off the old weld and fitting the new barrel hinge to the existing post. If the post itself moved, that price changes because the post work is the real repair.
Post Replacement
This is the job underneath most other gate jobs in Duncanville. The original posts on 1960s and 70s homes were set in shallow concrete pads, sometimes only 18 inches deep. Blackland Prairie clay swells after rain and contracts during drought, and over 40 years that cycle works a post loose like a loose tooth. We dig, set a new post at proper depth with proper concrete, and weld the gate back plumb. In Duncanville, a standard 4-inch square steel post replacement runs $450 to $750 depending on depth and whether it’s a driveway gate or a walk gate. If the gate itself is heavy ornamental iron, the post has to be larger and the price moves accordingly.
Rail Repair
The horizontal rails on older wrought-iron and tubular gates rust from the inside out. You’ll see rust staining below the welds, or flaking at the joints. If caught before the rail has lost its structure, we can cut out the bad section and weld in new steel, then repaint the repair to match. That runs $250 to $500 for a typical rail section on a Duncanville home. We’ll tell you honestly if the rail is too far gone and the whole panel needs rebuilding. Hal would rather save a gate than sell you a new one.
Custom Welding
Not every fix comes from a catalog. When a gate’s geometry doesn’t match off-the-shelf brackets, or a farm gate needs a receiver hitch welded on for a trailer, we do the custom work right in your driveway. Mobile welding to reinforce a sagging panel or fabricate a custom latch mount in Duncanville typically runs $150 to $400 depending on the steel and the time. We bring the welder, the generator, and the grinder. Your gate stays where it is.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Duncanville
We stock parts and we’re certified to service the operators Duncanville homeowners actually have: LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. If your automatic gate runs a BFT or a Linear board and it’s acting up, we likely have the part on the truck or can have it in hand within a day. For Viking and Ghost Controls swing-arm operators on acreage gates around the south edge of town, we handle the full range of arm replacement, limit adjustment, and loop detector repair.
Common Gate Parts & Welding Problems We See in Duncanville Homes
- Clay heave crushing underground conduit. Duncanville’s expanding clay doesn’t just move posts. It crushes the PVC conduit carrying loop detector wires and low-voltage operator cable. Your motor says “fault” but the actual failure is two feet underground, right at the hinge post. We diagnose it with a wire tracer before we ever unbolt the motor.
- Late-summer gate binding. As the black clay dries out in July and August, it shrinks away from post footings and hinge posts lean outward. By 3 to 5 PM, when the steel itself has also expanded in the heat, the gate won’t latch. This is a post problem, not a hinge problem. We fix the post.
- Wind and hail damage to slide tracks. Duncanville sits in a severe-weather corridor. Spring straight-line winds bend slide-gate tracks and knock swing gates off their hinge bolts. We’ve straightened racks and rehung panels after more than one north Texas storm front.
- Rust through on 50-year-old rails. Homes built in the 1960s and 70s around Duncanville often have original ornamental gates with rails rusting from the inside. By the time you see it, a section usually needs cut-and-weld replacement. That’s a repair we do weekly.
Pricing for Gate Parts & Welding in Duncanville, TX
Gate parts and welding pricing in Duncanville is driven by the same black clay that moves your posts. Here’s what you’re looking at:
- Hinge replacement: $180-$320 per hinge
- Post replacement (4-inch steel): $450-$750
- Rail section repair: $250-$500
- Custom welding / bracket fabrication: $150-$400
- Operator loop / conduit repair: $220-$480
Every price gets written down and agreed to before any work begins. We don’t show up and add a “soil surcharge.” The quote is the quote. There’s no trip charge inside Dallas County on repair calls over $200, and we take $40 off any repair over that amount. Seniors and veterans get a permanent 10% discount. Call (903) 829-4499 and we’ll give you a straight number over the phone.
We Also Serve Cities Near Duncanville
Our service area covers Duncanville and the surrounding communities, including DeSoto, Cedar Hill, Grand Prairie, and Irving. If you’re just outside the city line or on an acreage property between towns, we still come out. Whether you’re in the middle of Duncanville or just over the line into Duncanville territory from Cedar Hill, the same crew and the same guarantee apply. Call and ask.
Serving Duncanville, TX - Our Local Coverage Area
We’re based in the Duncanville area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Parts & Welding in Duncanville
Your hinge post has moved. Duncanville’s Blackland Prairie clay swells when wet and shrinks hard during summer drought. As the clay pulls away from a shallow 1960s footing, the post leans outward and the gate binds on the latch side by mid-afternoon, when the heat has also expanded the steel. The fix is resetting the post to a deeper footing and rehanging the gate, not just filing the latch. We do that job in Duncanville every week. Call (903) 829-4499 and we’ll take a look.
Yes. For acreage gates on the south and east edges of Duncanville where running conduit from the house isn’t practical, we install solar-powered operators and weld the mounting plate and rack directly to the gate frame. BFT, Viking, and Ghost Controls all make solar-capable 12V and 24V operators that handle wide farm gates. The welding is done on site, and the operator gets set for the gate’s actual weight and travel, not a guess. Call (903) 829-4499 for a free measure and written price.
Most of the time it’s repairable. The rails on Duncanville’s original ornamental gates rust from the inside where paint never reached, but if the surrounding steel still has wall thickness, we cut out the bad section, weld in new rail stock, grind the joints smooth, and repaint to match. A rail repair runs $250 to $500 in Duncanville. Replacing the whole panel is a last resort, and we’ll only recommend it when the rust has eaten through enough of the frame that welding new steel to it would be welding to lace. Get a second opinion from us free - we’ll tell you straight.
Because water is getting into a splice, a loop detector, or a partially crushed conduit joint, and the clay swelling after rain is flexing it just enough to break the connection. Duncanville’s soil movement means underground wiring here takes abuse that sandier DFW suburbs never see. We trace the wire, find the break, and repair the conduit so the same rain doesn’t kill it again. Loop and conduit repair in Duncanville runs $220 to $480. Call (903) 829-4499 and we’ll schedule the trace.
Usually the post needs to be reset. A farm gate with livestock leaning on it puts all the load on the hinge post, and in Duncanville’s clay that post has been moving for decades. If we just weld on a new hinge while the post leans, you’ll have the same problem in six months. We reset the post to a proper depth, then weld the hinges. If you need the gate hung same-day for livestock security, we’ll set the post in high-early concrete and brace it so the gate can hang within hours, then finish-grade the footing. Call (903) 829-4499 and tell us the gate width; we’ll bring what we need.
Set Up a Free Estimate in Duncanville
If your gate is leaning, binding, rusting, or just not closing like it used to, call (903) 829-4499. A live person answers, 24/7. We’ll talk through what you’re seeing, give you a straight answer on what it likely costs, and schedule a time to put eyes on it in Duncanville. Every estimate is free, every price is written before work starts, and every job carries the 90-Day Done Right Promise in writing. Hal’s name is on the shop. That’s the oldest accountability there is.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate, serving Duncanville and the surrounding DFW area since 2001.