Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Farm & ranch
Before
After
Before
After
Before
AfterTrusted Gate Parts & Welding for Grand Prairie Homeowners
When a gate hinge tears loose or a post gives way, the fix usually comes down to two things: the right parts and a weld that holds. Gate Parts & Welding - Grand Prairie is exactly what Hal Gatewood has been doing since 2001, and most repair jobs are handled the same day you call. We work on your gate right there in the driveway, not hauled off to some shop across the Metroplex. If you need hinge replacement, post repair, custom welding, or latch work done right the first time, call (903) 829-4499 and talk to a live person who knows gates.
What we’ve learned in 29 years of serving Grand Prairie, Irving, Arlington, and the surrounding communities is this: a gate fails at its weakest point, and that point is almost always where metal meets metal. The good news? That’s exactly what we weld, on site, with the gate still hanging where it belongs. No trailer fees, no mystery invoices. Just straight answers and a 90-Day Done Right Promise in writing on every single job.
What Our Gate Parts & Welding Service Includes
Gates are simple machines, but every part on them takes a beating from Texas sun, wind, and the ground shifting under Grand Prairie’s heavy clay soil. When one part fails, the rest of the gate starts working against itself. Here’s what we fix and how we go about it.
Hinge Replacement
A worn hinge is the most common reason a gate starts to drag or sag. Hinges carry the entire weight of the gate panel, and once they start to oval out or crack at the weld point, the gate drops a quarter inch, then a half inch, then stops latching altogether. We replace hinges with correctly sized, heavy-gauge hardware and weld them to the post and the frame so they don’t work loose again. In Grand Prairie and over in Bedford Gate Parts & Welding territory, we see a lot of gates that were hung on hinges that were too small for the panel from day one.
Post Replacement
The hinge post takes more abuse than any other component on a gate. Grand Prairie’s clay soil expands and contracts with the seasons, and a post that was set in a thin pour of concrete will lean, crack, or pull the gate out of alignment year after year. Setting a new post means digging out the old footing, dropping in a properly sized post, and welding the hinges back on square and plumb. We set the post deeper than most and use the correct concrete mix so you aren’t calling us again in three years.
Rail Repair
The horizontal rails on a welded gate frame are where stress cracks show up first, especially on heavier driveway gates. When a rail cracks through, the gate panel loses its structure, and the crack will spread down into the pickets if you let it go. We cut the cracked section out, sleeve or replace it, and weld it back with full penetration so the repair is as strong as the original frame. Often the repair is stronger, because we add gussets where the original builder skipped them.
Custom Welding
Some repairs don’t have an off-the-shelf part, and that’s where custom welding earns its keep. We fabricate brackets, repair caps, gate stops, drop rods, and reinforcement plates for gates that were built to no standard size. Hal himself has been welding since 2001 and will build a repair that matches the gate instead of making the gate match a store-bought part. If it’s steel, and it belongs on a gate, we can make it or fix it in place.
Gate Rollers
Cantilever and rolling gates get their smoothness from the rollers, and once a roller seizes or loses its bearings, the gate starts to shiver and bind on the track. We replace roller assemblies, weld on new brackets where the old mount has wallowed out, and get the gate rolling without grinding. On slide gates, a bad roller will destroy the track, and a new track costs a lot more than a new roller.
Latch & Lock
A gate that won’t stay closed isn’t just inconvenient, it’s a security risk. Latches wear out, strike plates move, and the post the latch grabs onto shifts until the whole latching system is a quarter inch out of line. We rebuild latch mounts, replace striker plates, adjust locking bars, and weld anything that’s meant to be welded so the gate closes solid and stays that way. If you have a keypad or automatic opener, we make sure the mechanical latch and the operator talk to each other.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Brands We Service for Gate Parts & Welding
We’re certified to service nine major gate brands, and the parts we weld and install are matched to what your gate was built with. BFT operators and hardware are common on higher-end residential gates in the Grand Prairie area, and we keep the correct hinge kits, limit brackets, and replacement hardware for them in the truck. A BFT gate that’s sagging or binding usually has one bad hinge or one shifted post, and that’s a repair we handle with OEM parts, not a box-store substitute.
Linear is another brand we see regularly on swing and slide gates across North Texas. The operator is usually fine; the trouble is generally the steel the operator is attached to. We’ve welded hundreds of Linear gate frames that cracked at the hinge or the operator mount, and we use the right filler rod and heat settings so the repair doesn’t introduce new weak spots. The same goes for Viking and Ghost Controls hardware: the brand matters for the electronics, but the metal repair is where craftsmanship decides whether the job lasts five years or twenty. White-glove, red-carpet work, plain and simple. And if your gate uses a brand we haven’t named here, we can still fix it. Metal is metal, and we’ve been reading it since 2001.
Signs You Need Gate Parts & Welding Right Now
- The gate drags on the ground or scrapes the track. This is almost always a hinge or post problem, not a gate panel problem. The longer it drags, the more metal you’re grinding off the bottom rail. We’re out in Grand Prairie most days, and we can usually get the gate lifting and swinging the same afternoon.
- The gate won’t stay latched. If the latch isn’t meeting the striker plate, the post has moved or the hinges have worn. A gate that won’t stay closed is a security risk, not a minor annoyance. Call us before the gate gets forced open and the damage spreads.
- You can see a crack forming around a weld. This is the one you shouldn’t wait on. A cracked weld tells you the structure is under stress, and the crack will grow until the rail fails completely. We grind the old weld out and re-weld it with proper penetration, plus a gusset if the design calls for it.
- The gate squeals or binds when it rolls. Roller bearings on slide gates wear out, and when they do, the gate grinds against the track. Replace the roller now and the track survives. Keep running it and the roller eats the track rail, which is a much bigger job.
- The post is leaning or pulling out of the ground. A leaning post in Grand Prairie clay means the original footer wasn’t set deep enough or the post is rusting below the soil line. We set new posts at the right depth with the right concrete and weld the gate back on square.
Our Gate Parts & Welding Process - Step by Step
We don’t make a production out of it. You’ll know exactly what we’re doing, how much Gate Parts & Welding costs, and when we’ll be done before we light the welder.
- 1
You call and talk to a live person. That’s the whole spiel. No phone tree, no voicemail. Call (903) 829-4499 and describe what the gate is doing. We’ll let you know what it sounds like and whether we need to see it in person to quote it.
- 2
We walk the gate with you. Arcs and sparks come later. First we look at the hinges, posts, rails, rollers, and latch together. We’ll show you what failed, and we’ll show you why it failed. You’ll know what we’re quoting before we quote it.
- 3
You get a written price before any work starts. The price we quote is the price you pay. No surprise line items, no “well, once we got into it.” We’ve been doing this long enough to price the job correctly from the ground.
- 4
We weld and replace, on site, most jobs same day. The gate stays in your driveway. We bring the welder, the parts, and the right hardware to the gate, not the other way around. Most hinge, latch, and rail repairs are done in an afternoon.
- 5
You get the 90-Day Done Right Promise in writing. Every job, stamped in writing. If it’s not done right, we make it right. One call brings Hal back, no runaround. That’s the promise, and it isn’t buried in fine print.
How Much Does Gate Parts & Welding Cost in Grand Prairie?
A typical hinge replacement on a residential swing gate in Grand Prairie runs $180 to $340, depending on how many hinges and whether the post needs re-welding. Post replacement is a bigger job because of the concrete work: most single-post replacements land between $450 and $900 dug out, set, and welded back. Rail repairs usually fall in the $220 to $500 range, custom welding is quoted by the hour and the job, and roller replacement typically runs $150 to $400 per gate, depending on roller quality and how many carriers are shot. Latch and lock repairs are usually $120 to $300.
What moves the price: how bad the rust is, whether the post is still structurally sound, and how much grinding and prep the weld needs. We don’t pad quotes with “miscellaneous” anything. One more thing we do: we keep a permanent 10% discount for seniors and veterans, and right now there’s $40 off any repair over $200. Call (903) 829-4499 and you’ll get an exact price in writing, with the discount already applied, before we touch a tool.
Gate Parts & Welding Near Grand Prairie - Our Service Area
We cover Grand Prairie, Irving, Arlington, Duncanville, Kennedale, Euless, Bedford, Hurst, Cedar Hill, Mansfield, DeSoto, and Oak Cliff. If you’re inside the county, there’s no trip charge. If you need Gate Parts & Welding in Irving or Gate Parts & Welding in Arlington, we handle those every week. Same crews, same owner, same promise. We answer the phone 24 hours a day, 7 days a week, so if you call at six in the morning or ten at night, a real person picks up. We’re based right down the road, and you can find the home shop address published on the site. That’s how we’ve been doing it since 2001, and we don’t see a reason to change it.
Serving Grand Prairie, TX - Our Local Coverage Area
We’re based in the Grand Prairie area and also handle Gate Parts & Welding - Euless, so we know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
Frequently Asked Questions - Gate Parts & Welding in Grand Prairie
Gate parts and welding is the repair and fabrication of the metal components that make a gate work: hinges, posts, rails, rollers, latches, and brackets. It includes replacing worn parts and welding cracked or broken metal back to full strength. We also provide Gate Parts & Welding in Duncanville, and at Gatewood Fence & Gate, we do all of it on site in Grand Prairie, so you’re not without a gate while it sits in a shop.
Most hinge, latch, and rail repairs are done the same day we arrive. Post replacement takes longer because the concrete has to set before the gate goes back on, usually two to three days total. We’ll give you a clear timeline when we quote the job.
Hinge replacement typically runs $180 to $340, post replacement $450 to $900, rail repair $220 to $500, and custom welding varies by the job. Every quote is in writing before the work begins, and seniors and veterans get a 10% discount. Call (903) 829-4499 and we’ll give you an exact number.
Yes, we service BFT operators and hardware regularly, and we keep the correct parts and hinge kits for BFT gates in inventory. We’re also certified on Linear, Viking, Ghost Controls, and several other major brands, so the parts we install match what your gate was built with.
Most Grand Prairie jobs are handled the same day you call, especially if the gate is off its hinges or the latch has failed and the gate won’t secure. We answer the phone 24/7, and Hal or one of his crew will be out as soon as the job can be done right. We’ve been been serving the area since 2001, and if you need Gate Parts & Welding in Grand Prairie, you’ve already found the right shop.
Every job carries the 90-Day Done Right Promise in writing. If something isn’t right within 90 days, one call brings us back to make it right. No fine print, no “depending on the circumstances.” The promise is stamped on every invoice, not hidden in the paperwork.
Not much to do. Clear a path to the gate on both sides, make sure we can get a truck close enough to run the welder, and unlock the gate if it still latches. If you have dogs that aren’t fond of strangers, let them in the house. We’ll handle the rest.
Schedule Your Gate Parts & Welding Service in Grand Prairie Today
This is the part where you call, and a real person answers. We’ll talk about what the gate is doing, get you a written price with no trip charge inside the county, and get it fixed right, most jobs same day. Call (903) 829-4499 for a free estimate. Hal Gatewood, owner at Gatewood Fence & Gate, serving Grand Prairie since 2001.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate, serving Grand Prairie since 2001.