Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Farm & ranch
Before
After
Before
After
Before
AfterGhost Controls Gate Repair in Grand Prairie, TX | Gatewood Fence & Gate
We handle Gate Repair in Grand Prairie for Ghost Controls operators all over the city, and we do it as an independent service provider, not a manufacturer affiliate. The thing that sets our Ghost Controls work here apart is simple: we know this city’s soil and this city’s industrial traffic, and we know how both of them beat up the same operator in different ways. If your Ghost Controls gate is acting up in Grand Prairie, call (903) 829-4499 and we’ll tell you what’s wrong before we ever touch a screwdriver.
Why Grand Prairie Residents Choose Us for Ghost Controls Service
Hal Gatewood has been fixing gates in Grand Prairie since 2001. Most folks around the Dalworth Park neighborhood know his truck on sight. He picked up the welding and mechanical side of the trade at Tarrant County College’s vocational program before going out on his own, and the reason he started Gatewood Fence & Gate still drives how we work today: he kept running into homeowners left with gates that didn’t work right, bad welds, wrong hardware, or who needed our Gate Installation in Grand Prairie done right because operators were put in without reading a spec sheet. It bothered him then and it bothers us now.
We handle Ghost Controls sales & service the way we handle every brand we work on. We stock OEM Ghost Controls control boards and remotes for warranty-era units, and for older out-of-warranty operators we field proven aftermarket boards and sealed wiring kits when stock delays would otherwise leave you waiting two weeks for a same-week fix. On-site welding means your gate stays in your driveway. We fix the panel without hauling it off, and we fix the root problem without swapping parts that don’t need swapping. A live person answers our phone 24/7. Not a voicemail, not a call center three states away. Somebody who actually knows gates.
Common Ghost Controls Gate Repair Problems We Solve in Grand Prairie
- Error code 43 (motor overcurrent) on panel-style slide operators. We see this constantly along the SH 161 industrial corridors and around the Great Southwest Industrial District, where clay and debris pile into the ground rail after storms. The motor trips, the board throws the code, and the gate stops mid-travel. We clear the rail, check the chain, and reset the limit switch properly.
- Water intrusion behind the J-box and corrosion at the wiring harness. North Texas hail cracks the weatherhead gasket, and winter ice storms work water into places it should never be. On residential installs across Grand Prairie, we find green corrosion on the harness terminals and blown boards that trace straight back to a failed gasket.
- Premature chain or belt stretch on high-cycle commercial slide gates. We work warehouse docks off I-20 and Trinity Blvd where a Ghost Controls operator runs 50 to 100 cycles a day. That’s fine for a commercial-duty unit, but when somebody spec’d a residential Ghost Controls operator, the chain stretches and pitches links within months. We replace the drive and tell you honestly whether the operator belongs on that gate.
- Battery packs swelling and pushing the operator cover off. South Grand Prairie summers regularly exceed 100°F, and the 16-inch gel-acid battery packs in Ghost Controls swing arm operators don’t love that heat. We’ve opened operators where the pack had swollen enough to bow the cover. We replace the pack and check the charging circuit so it doesn’t happen again in August.
- Swing gates binding and dragging on older Grand Prairie lots. The 1960s-to-1980s neighborhoods near Dalworth Park have wrought-iron gates set in original concrete footings, and Blackland Prairie clay has been heaving those footings for decades. The gate drags, the operator labors, and the board eventually faults. Fix the post and the footings first, or you’ll fix the board twice.
Ghost Controls Service in Grand Prairie: What Local Conditions Mean for Your Equipment
Here’s the thing nobody tells you about Grand Prairie gate repair: the soil is the problem more often than the operator is. Blackland Prairie clay swells hard after spring rains and shrinks hard during summer droughts, and that cycle tilts gate posts out of plumb. On older Dalworth Park lots, we routinely see a Ghost Controls operator’s drive rail get pulled out of alignment within 14 to 18 months just from post heave. The same operator on Arlington’s sandy loam would stay aligned for years. So when a Ghost Controls gate in Grand Prairie starts binding, dragging, or throwing motor faults, the answer isn’t always a new control board. A binding gate here is often a footer problem, not a board problem. We check the post, the rail, and the limit switch before we ever condemn the electronics. A gate sags in the hinge post, not in the middle, and that is where we start.
Ghost Controls Models & Products We Service in Grand Prairie
We service the full Ghost Controls residential and light-commercial line: TSS1 and TDS1 series slide gate operators, swing arm operators with the 16-inch gel-acid battery packs, A20 and A30 series dual-swing residential kits, and inline and rack-and-pinion slide motors. When a unit is still under warranty, we order OEM Ghost Controls boards and remotes. When it’s not, we use proven aftermarket parts that get your gate running this week instead of next month. We keep common boards, remotes, and sealed wiring kits stocked for fast Grand Prairie turnaround, so you’re not waiting on a ground shipment while your gate sits open.
Ghost Controls Service Pricing in Grand Prairie
Most Ghost Controls repair calls in Grand Prairie land between $180 and $450, depending on what’s actually failed. A limit switch reset or rail clearing runs on the low end. A control board replacement runs higher. A full operator replacement on a South Grand Prairie dual-swing system runs $850 to $1,500 installed. Here’s what you get before any of that: a free estimate, a price you agree to in writing before any work starts, and a written 90-Day Done Right Promise on the repair. We don’t quote one number on the phone and charge another at the door. Call (903) 829-4499 and we’ll walk through what you’re seeing, then give you a straight price.
Serving Grand Prairie, TX - Our Local Coverage Area
We’re based in the Grand Prairie area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Ghost Controls Gate Repair in Grand Prairie
Error 43 means the motor is drawing too much current, and in that part of Grand Prairie the usual cause is debris packed into the ground rail, especially after storms wash clay and cardboard scraps down the SH 161 corridor. The rail fills up, the gate stalls, and the board shuts the motor down to protect it. We clear the rail, check the chain for pitched links, and verify the limit switch, then the gate runs clean again. Call (903) 829-4499 for an exact quote.
It can, as long as the gate is balanced and the posts stay plumb. The problem on older Grand Prairie lots is that expansive clay heaves the footings and throws the gate out of plumb, which forces the operator to work against the gate’s own weight. The A30 series has the torque to handle a double iron gate, but no operator survives a gate that drags. We fix the post first, then the operator. Show me the gate closing on its own and I’ll show you where it’s failing.
Twice a year is right for most South Grand Prairie homes. Spring is the critical one, after the clay has done its swelling and the gate has likely shifted. We check the drive rail alignment, lube the chain or belt, test the limit switches, and inspect the battery pack and weatherhead gasket. It takes about an hour and it heads off most of the failures we see in July and August.
No. The photocell sensor is a separate component, and we replace it on its own. What hail sometimes damages alongside the sensor is the weatherhead gasket or the plastic enclosure on the operator itself. If the board got wet after the hail cracked the housing, that’s a board replacement. But the operator usually survives. Call (903) 829-4499 and we’ll tell you what actually needs replacing.
Usually yes, if the grinding is the drive chain or belt and not the motor itself. Ice storms crack enclosures and let water in, which corrodes the drive components long before the board dies. If the grinding is a worn chain or a dry rail, that’s a same-day fix. If the motor bearings are shot, we’ll tell you straight and price a replacement. Either way, the estimate is free and the price is fixed before we start. Call (903) 829-4499.
Service Areas Near Grand Prairie
We serve Grand Prairie service area and the surrounding cities. If you’re in Ghost Controls service in Irving or Ghost Controls service in Arlington, we cover those too. We also take calls from Duncanville, Kennedale, and Euless. If you’re within range, we’ll be there.
Book Your Ghost Controls Service in Grand Prairie Today
Tell me what it’s doing, and I’ll tell you what it needs. No runaround. Call (903) 829-4499 for a free estimate. Same-day service is available for most repair calls in Grand Prairie, and the price is quoted and agreed before any work begins.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate, serving Grand Prairie since 2001.